By in

PRIMERS FOR CORK COVERINGS

Primers for cork coverings

CorkHouse primer

Water-based primer for application by roller or brush.

Basic delivery form

– Primer CorkHouse is a ready-to-use aqua dispersion for application by roller or brush under the CorkHouse varnish for protective covering.

Application area

– the use of on the exotic species of wood is limited, suitable only for covering the wood with low oil content, a trial application is recommended.

Properties

– very well fills the pores especially suitable for wood species with good absorbency, beech, maple, ash it is not recommended to work with a spatula. Reduces the possibility of gluing individual parquet strips along the side edges, allowing you to achieve a homogenous color tone of the covering. The effect of “burning” wood is achieved, when used on oak, the product is easy to use, has a faint smell and an environmentally friendly.

Mode of application

– before the production implementation the CorkHouse primer should be well shaken. The wood surface should be cleansed from dust, oil, wax, grease and any other substance residues.
We recommend to grind the surface of the wood with an abrasive grinding grating grain.

Primer

– Apply a layer of CorkHouse primer by roller or brush; the consumption is about 100 g / m2, depending on the absorbency of the wood, CorkHouse primer can be also sprayed. We would be happy to advise you on this topic.
Drying time 2 hours under normal conditions (temperature + 20 ° C and relative humidity 55%). High humidity and low temperature slows down the drying process. Make sure that the room is well ventilated, avoid draughs. After applying the primer, do not perform an intermediate grinding.

Working tools

– If the CorkHouse primer was applied using a roller or paint brush, CorkHouse recommends: after work was completed, clean the instrument with newsprint or paper with a similar absorbency and wash with water.
The room temperature should not be below + 15 ° C and not exceed + 25C.

Storage conditions

– Store and transport at a temperature not lower than + 6 ° C.
Primer is needed for any facing materials that you will need to paint later. In the same way, a primer is needed for a cork coverings- because without it, the paint will be poorly absorbed, and hold not so long. Of course, such cork products are rarely used, because the cork coverings themselves look very nice, and the coloring needs technical cork material, and even not always. But any changes in the interior design are possible, and in such cases, a primer is needed. It is worth noting that if you buy a cork for walls immediately lacquered, the primer will not be needed, as far as there will simply not be any positive adhesion effect from it.

By in

VARNISH COVERING

Professional varnish covering FROM CORK HOUSE

CorkHouse varnish is a two-component waterborne lacquer made in Germany. It withstands loads from normal to very high, gives light shades to surfaces. Suitable for covering floors in sport halls (meets the requirements of DIN 18032, part 2)

Package: Delivered in containers with the capacity: 0,9 l CorkHousvarnish and 0.045 L CorkHouse Platinum Iso-Harter hardener; 4.5 L CorkHouse varnish and 0.225 L CorkHouse Platinum Iso-Harter hardener

The containers are filled in such a way that it is possible to easily mix the components of the lacquer / hardener mixture

Properties:

– very high abrasion resistance
– not yellowed
– lightresistant
– very ease of use
– quick drying
– very good grinding
– high resistant to the effects of household chemicals
– extremely high resistant to abrasion and scratches
– has a weak odor
– water resistant (even with prolonged exposure to a continuous varnish covering)

Mode of application:

In the container with CorkHouse varnish add CorkHouse Platinum Iso-Harter hardener and shake well (at least 15 seconds). Mix only a the quantity of varnish and hardener, that volume can be applied in the next 2 hours. Component ratio: 20: 1 lacquer / hardener

By in

CONTACT ADHESIVE

Professional CorkHouse contact adhesive for cork coverings

Purpose:

Contact adhesive for adhesive cork coverings, as well as for gluing the technical cork to fiberboard/chipboard, concrete and other materials.

Application:

The surface must be clean, dry and even. The adhesive is covered by a thin, even layer on both glued surfaces – the velor roller for the cork covering and the notched trowel on the base. The covering is attached not earlier than 15 – 20 minutes.

The working condition of the adhesive after application is up to 2 hours. For high-quality attaching, it is enough to press the tile on the entire surface while laying, tile peeling and re-gluing is not allowed. Complete drying of the adhesive takes 48 hours.

Consumption of glue:

250 – 300 g / square meter on each of the surfaces to be bonded.

Method of application:

Velor roller or notched trowel.
Storage: Sealed, up to 12 months at a temperature of 10 – 25 degrees Celsius.
The main product, which is always bought together with cork coverings, almost any type, is a contact adhesive for cork. With this adhesive any coverings are attached – both sheeted on the floor, and rolled or in the form of wallpaper on the wall. Here you can buy a glue for cork coverings for walls of various types – both water-based and rubber-based, from the leading manufacturers in this industry. The price for cork coverings glue is relatively low, and in general do not try to safe maney on its quality, since the strength with which the covering will be hold on to the same wall depens on its quality. We sell very good adhesives, which can be used even in conditions of high humidity, and they keep perfectly even heavy sheets with a thickness of more than 10 mm. There is no need for further maintenance of this fastening.

If you want to buy cork glue, our specialists will advise you the best choice, depending on what kind of material for the walls is used, and what kind of covering. The main advice is to buy all goods for cork covering at once together with the coverings themselves, in order to clearly understand the volumes of the forthcoming works. If you want to buy a cork for walls – you always need to understand that for its fastening you will also need a sufficient amount of contact adhesive, except perhaps self-adhesive wallpaper or thick sheets, which will be attached somehow differently, for example, using screws.

RELATED PRODUCTS
By in

RELATED PRODUCTS

RELATED PRODUCTS FROM CORK HOUSE

PROFESSIONAL CONTACT ADHESIVE FOR CORK COVERINGS

Cork House contact adhesive for glue-down cork coverings, produced by BASF technology (Germany).

Read more…

PROTECTIVE COVERINGS FOR CORK FLOORS: VARNISH, OIL, WAX

Two-component parquet water-based Cork House varnish in Germany. It holds up the loads from normal to very high. Suitable for floors in sport halls.

Read more…

PRIMERS FOR CORK COVERINGS

Primer CorkHouse is a ready-to-use aqua dispersion for application by roller or brush under the CorkHouse varnish for protective covering.

Read more…